( 1 /10) 2002-01-09 (ver.0.2) liquid crystal display division product information features (1) 10.4 ? xga display size for notebook pc (2) lvds interface system (3) slim(5.7mmmax) & light weight design mechanical specifications item specifications dimensional outline ( typ.) 238.6( w ) x 173.2( h ) x 5.7max( d ) mm number of pixels 1024( w ) x 768( h ) pixels active area 210.432( w ) x 157.824( h ) mm pixel pitch 0.2055( w ) x 0.2055( h ) weight (approximately) 270 g backlight single ccfl, sidelight type absolute maximum ratings item min. max. unit ( v dd ) -0.3 4.0 v supply voltage ( v fl ) 0 2.0 kv( rms) fl driving frequency ( f fl ) - 100 khz input signal voltage ( v in ) -0.3 v dd +0.3 v operating temperature 0 50 c storage temperature -20 60 c storage humidity 10 90 %(rh) electrical specification item min. typ. max. unit remarks ( v dd ) 3.0 3.3 3.6 v supply voltage ( v fl ) 540 590 640 v( rms) i fl =5 ma( rms) fl start voltage ( t a=0 c) 1200 --- 1600 v( rms) receiver input voltage 0 --- 2.4 v differential input high threshold( v th )*1 --- --- v os +0.1 v differential input low threshold( v tl )*1 v os -0.1 --- --- v v os :offset mode voltage v os =+1.2v *2 ( i dd ) --- 230 --- ma( rms) current consumption *3 ( i fl ) 3.0 5.0 6.0 ma( rms) *2 *3 power consumption --- 3.7 --- w *1 : refer to df90cf364 specification by national semiconductor corporation. this lcd module conforms to lvds standard (tia/eia-644) *2 : 8 color bars pattern *3 : excepting the efficiency fl inverter ?@?@?@?@?@ *4 : not use hsync nor vsync. only enab control. optical specification ( t a=25 c) item min. typ. max. unit remarks contrast ratio ( cr ) 100 250 --- --- ( t on ) --- --- 50 ms response time ( t off ) --- --- 50 ms luminance ( l ) --- 150 --- cd/m 2 i fl =5ma( rms) *the information contained herein is presented only as a guide for the applications of our products. no responsibility is assumed by toshiba or other rights of the third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of toshiba or others. *the information contained herein may be changed without prior notice. it is therefore advisable to contact toshiba before proceeding with the design of equipment incorporating this product. 26cm colour tft-lcd module (10.4 type) LTM10C313U ( p- si tft) xga t entative
( 2 /10) 2002-01-09 (ver.0.2) LTM10C313U dimensional outline (front figure) unit : mm standard tolerance : +/- 0.5
( 3 /10) 2002-01-09 (ver.0.2) LTM10C313U block diagram 1, 1 2, 1 x2 n-1 , 1 x2 n , 1 1024, 1 1, 2 1, y x 2n-1 , y x 2n , y 1, 768 1024,768 cn2 connector dc/dc converter panel controller +lvds gray scale manipulation voltage generation circuit y-driver liquid crystal panel 1024 x 768 pixels x-driver backlight 1024 pixels 768 pixels d/a converter circuit cn1 fpc i/f pcb
( 4 /10) 2002-01-09 (ver.0.2) LTM10C313U timing chart v v v v v a l i d d a t a t c i h t s t c t h t c t c i l 5 t 1 0 2 3 , y 1 0 2 4 , y 1 0 2 2 , y 1 0 2 1 , y x , y t 1 c l k i n t 2 c l k i n t 1 i n 0 - 2 0 t 2 i n 0 - 2 0 b 5 - b 0 g 5 - g 0 e n a b r 5 - r 0 n c l k 7 , y 6 , y 5 , y 4 , y 3 , y 2 , y 1 , y t 5 ( 1 ) v e r t i c a l t i m i n g ( 2 ) h o r i z o n t a l t i m i n g b 5 - b 0 g 5 - g 0 r 5 - r 0 n c l k e n a b e n a b n c l k b 5 - b 0 g 5 - g 0 r 5 - r 0 x , 4 x , 2 x , 7 6 7 x , 7 6 8 x , y x , 3 x , 1 1 t 2 t 3 t 3 4 t t i h ( m i n ) : 0 . 8 v d d ( v ) i l ( m a x ) : 0 . 2 v d d ( v ) i h ( m i n ) : 0 . 8 v d d ( v ) i l ( m a x ) : 0 . 2 v d d ( v )
( 5 /10) 2002-01-09 (ver.0.2) LTM10C313U timing specification 2) 3) 4) item symbol min. typ. max. unit remarks frame period t 1 778 x t 3 806 x t 3 16.67 860 x t 3 17.78 --- ms 1) 5) vertical display term t 2 768 x t 3 768 x t 3 768 x t 3 --- 1) 5) one line scanning time t 3 1336 x t 5 20.04 1344 x t 5 20.68 1462 x t 5 --- --- m s 1) 5) horizontal display term t 4 1024 x t 5 1024 x t 5 1024 x t 5 --- 1) 6) clock period t 5 15.0 15.38 --- ns note 1) refer to timing chart at page4 and lvds specification (ds90cf364) by national semiconductor corporation. note 2) if enab is fixed to "h" or "l" level for certain period while nclk is supplied, the panel displays black with some flicker. note 3) don't fix nclk to "h" or "l" level while the vdd(+3.3v) is supplied. if nclk is fixed to "h" or "l" level for certain period while enab is spplied , the panel may be damaged. when i t holds on, dc voltage supplies to liquid crystal materials and i t may cause damage to liquid crystal materials. graphic controller 69000 (chips & technology), for example, causes above phenomenon note 4) please adjust lcd operating signal timing and fl driving frequency, to optimize the display quality. there is a possibility that flicker is observed by the interference of lcd operating signal timing and fl driving condition (especially driving frequency), even if the condition satisfies above timing specifications and recommended operating conditions shown in 3. note 5) do not make t 1, t 2 and t 3 fluctuate. if t 1, t 2 and t 3 are fluctuate, the panel displays black. note 6) keep constant the number of clock within one line scanning time and the number of scanning line within one flame period sequence of power supplies and signals i n 0 - ?` i n 2 - c l k - i n 0 + ?` i n 2 + c l k + 1 0 % 1 0 % d d 0 . 2 v 0 . 2 v 0 . 2 v 1 0 m s ( m a x . ) 5 0 0 m s ( m i n . ) 4 0 m s ( m a x . ) 0 m s ( m i n . ) 1 0 m s ( m a x . ) 3 . 0 v 3 . 0 v v 2 0 u s ( m i n . ) 4 0 m s ( m a x . ) 0 m s ( m i n . )
( 6 /10) 2002-01-09 (ver.0.2) LTM10C313U connector pin assignment for interface cn1 input signal connector :df19l-14p-1h / hirose electric co.,ltd mating connector : df19g-14s-11c(housing) / hirose electric co.,ltd terminal no. symbol function 1 v dd power supply : +3.3v 2 v dd power supply : +3.3v 3 gnd 4 gnd 5 in0- transmission data of pixels 0 (negative : - ) 6 in0+ transmission data of pixels 0 (positive : + ) 7 in1- transmission data of pixels 1 (negative : - ) 8 in1+ transmission data of pixels 1 (positive : + ) 9 in2- transmission data of pixels 2 (negative : - ) 10 in2+ transmission data of pixels 2 (positive : + ) 11 clk- sampling clock (negative : - ) 12 clk+ sampling clock (positive : + ) 13 gnd 14 gnd cn2 ccfl power source connector : hv-2s-c1/japan aviation electronics industry., ltd mating connector : hv-2p-hf/ japan aviation electronics industry., ltd terminal no. symbol function 1 v fll ccfl power supply (low voltage) 2 v flh ccfl power supply (high voltage)
( 7 /10) 2002-01-09 (ver.0.2) LTM10C313U recommended transmitter (ds90cf363) to LTM10C313U interface assignment c ase1: 6bit transmitter ds90cf363 input terminal no. input signal (graphics controller output signal) LTM10C313U interface (cn1) symbol ds90cf363 symbol function output signal symbol terminal symbol tin0 44 r0 red pixels display data (lsb) tin1 45 r1 red pixels display data tin2 47 r2 red pixels display data tin3 48 r3 red pixels display data tin4 1 r4 red pixels display data tin5 3 r5 red pixels display data (msb) tin6 4 g0 green pixels display data (lsb) tout0- tout0+ no.5 no.6 in0- in0+ tin7 6 g1 green pixels display data tin8 7 g2 green pixels display data tin9 9 g3 green pixels display data tin10 10 g4 green pixels display data tin11 12 g5 green pixels display data (msb) tin12 13 b0 blue pixels display data (lsb) tin13 15 b1 blue pixels display data tout1- tout1+ no.7 no.8 in1- in1+ tin14 16 b2 blue pixels display data tin15 18 b3 blue pixels display data tin16 19 b4 blue pixels display data tin17 20 b5 blue pixels display data (msb) tin18 22 nc non connection (open) tin19 23 nc non connection (open) tin20 25 enab compound synchronization signal tout2- tout2+ no.9 no.10 in2- in2+ clk in 26 nclk data sampling clock tclk out- tclk out+ no.11 no.12 clk- clk+ g 0 r 5 r 4 r 3 r 2 r 1 r 0 g 5 b 0 b 1 g 4 g 1 b 4 b 5 g 3 g 2 b 2 b 3 n c n c e n a b i n 0 i n 1 i n 2 t i n 4 t i n 3 t i n 2 t i n 1 t i n 0 t i n 1 3 t i n 1 2 t i n 1 1 t i n 1 0 t i n 9 t i n 8 t i n 7 t i n 2 0 t i n 1 9 t i n 1 8 t i n 1 7 t i n 1 6 t i n 1 5 t i n 1 4 t i n 6 t i n 5
( 8 /10) 2002-01-09 (ver.0.2) LTM10C313U recommended transmitter ( ds90cf383) to LTM10C313U interface assignment c ase2: 8bit transmitter ds90cf383 input terminal no. input signal (graphics controller output signal) LTM10C313U interface (cn1) symbol ds90cf383 symbol function output signal symbol terminal symbol tin0 51 r0 red pixels display data (lsb) tin1 52 r1 red pixels display data tin2 54 r2 red pixels display data tin3 55 r3 red pixels display data tin4 56 r4 red pixels display data tin6 3 r5 red pixels display data (msb) tin7 4 g0 green pixels display data(lsb) tout0- tout0+ no.12 no.11 in0+ in0- tin8 6 g1 green pixels display data tin9 7 g2 green pixels display data tin12 11 g3 green pixels display data tin13 12 g4 green pixels display data tin14 14 g5 green pixels display data(msb) tin15 15 b0 blue pixels display data (lsb) tin18 19 b1 blue pixels display data tout1- tout1+ no.10 no.9 in1+ in1- tin19 20 b2 blue pixels display data tin20 22 b3 blue pixels display data tin21 23 b4 blue pixels display data tin22 24 b5 blue pixels display data (msb) tin24 27 nc non connection (open) tin25 28 nc non connection (open) tin26 30 enab compound synchronization signal tout2- tout2+ no.8 no.7 in2+ in2- tin27 50 nc non connection (open) tin5 2 nc non connection (open) tin10 8 nc non connection (open) tin11 10 nc non connection (open) tin16 16 nc non connection (open) tin17 18 nc non connection (open) tin23 25 nc non connection (open) tout3- tout3+ clk in 31 nclk data sampling clock tclk out- tclk out+ no.6 no.5 clk+ clk- g 0 r 5 r 4 r 3 r 2 r 1 r 0 g 5 b 0 b 1 g 4 g 1 b 4 b 5 g 3 g 2 b 2 b 3 n c n c e n a b i n 0 i n 1 i n 2 n c n c i n 3 n c n c n c n c n c t i n 2 2 t i n 2 1 t i n 2 0 t i n 1 9 t i n 2 3 t i n 1 7 t i n 1 6 t i n 1 1 t i n 1 0 t i n 5 t i n 2 7 t i n 7 t i n 6 t i n 4 t i n 3 t i n 2 t i n 1 t i n 0 t i n 1 8 t i n 1 5 t i n 1 4 t i n 1 3 t i n 1 2 t i n 9 t i n 8 t i n 2 6 t i n 2 5 t i n 2 4
( 9 /10) 2002-01-09 (ver.0.2) LTM10C313U 256k (k=1024) colors combination table display r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 gray scale level black l l l l l l l l l l l l l l l l l l - blue l l l l l l l l l l l l h h h h h h - green l l l l l l h h h h h h l l l l l l - light blue l l l l l l h h h h h h h h h h h h - red h h h h h h l l l l l l l l l l l l - purple h h h h h h l l l l l l h h h h h h - yellow h h h h h h h h h h h h l l l l l l - basic color white h h h h h h h h h h h h h h h h h h - black l l l l l l l l l l l l l l l l l l l 0 l l l l l h l l l l l l l l l l l l l 1 l l l l h l l l l l l l l l l l l l l 2 : : : : : : l3 ? l60 h h h h l h l l l l l l l l l l l l l61 dark - light h h h h h l l l l l l l l l l l l l l62 gray scale of red red h h h h h h l l l l l l l l l l l l red l63 black l l l l l l l l l l l l l l l l l l l 0 l l l l l l l l l l l h l l l l l l l 1 l l l l l l l l l l h l l l l l l l l 2 : : : : : : l3 ? l60 l l l l l l h h h h l h l l l l l l l61 dark - light l l l l l l h h h h h l l l l l l l l62 gray scale of green green l l l l l l h h h h h h l l l l l l green l63 black l l l l l l l l l l l l l l l l l l l 0 l l l l l l l l l l l l l l l l l h l 1 l l l l l l l l l l l l l l l l h l l 2 : : : : : : l3 ? l60 l l l l l l l l l l l l h h h h l h l61 dark - light l l l l l l l l l l l l h h h h h l l62 gray scale of blue blue l l l l l l l l l l l l h h h h h h blue l63 black l l l l l l l l l l l l l l l l l l l 0 l l l l l h l l l l l h l l l l l h l 1 l l l l h l l l l l h l l l l l h l l 2 : : : : : : l3 ? l60 h h h h l h h h h h l h h h h h l h l61 dark - light h h h h h l h h h h h l h h h h h l l62 gray scale of white & black white h h h h h h h h h h h h h h h h h h white l63
( 10 /10) 2002-01-09 (ver.0.2) LTM10C313U for safety lcd module is generally designed with precise parts to achieve light weighted thin mechanical dimensions. in using our modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed in engineering information no.ee-n001,"cautions and instructions for toshiba lcd modules". refer to individual specifications and technical data sheets (hereinafter called "td") for more detailed technical information. 1) special purposes a) toshiba's standard lcd modules have not been customized for operation in extreme environments or for use in applications where performance failures could be life-threatening or otherwise catastrophic. b) since toshiba's standard lcd modules have not been designed for operation in extreme environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed toshiba's published specification limits. c) in addition, since toshiba standard lcd modules have not been designed for use in applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to traffic collision avoidance system and air traffic indicator), in military defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear energy), or in critical medical device or patient life-support systems. 2) disassembling or modification do not disassemble or modify the module. it may damage sensitive parts inside lcd module, and may cause scratches or dust on the display. toshiba doses not warrant the module, if customer disassembled or modified it. 3) breakage of lcd panel do not ingest liquid crystal material, do not inhale this material, and do not contact the material with skin, if lcd panel is broken and liquid crystal material spills out. if liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately. if this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water. 4) glass of lcd panel be careful with chips of glass that may cause injuring fingers or skin, when the glass is broken. 5) electric shock disconnect power supply before handling lcd module. do not touch the parts inside lcd module and the fluorescent lamp's connector or cables in order to prevent electric shock, because high voltage is supplied to these parts from the inverter unit while power supply is turned on. 6) absolute maximum ratings and power protection circuit do not exceed the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise lcd module may be damaged. employ protection circuit for power supply, whenever the specification or td specifies it. suitable protection circuit should be applied for each system design. 7) disposal when dispose lcd module, obey to the applicable environmental regulations. !
|
